Solid-state-logic 82BN0M01B Bedienungsanleitung Seite 38
- Seite / 52
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 34 Nucleus User Guide
CHANNEL CONTROL
Channel Scrolling
On sessions with more than 16 channels, the CHANNEL and BANK switches allow you to choose
which DAW channels are controlled by the 16 Nucleus faders.
To scroll the Nucleus through the DAW channels in increments of one, use the left and right
CHANNEL switches. To scroll in increments of 16 DAW channels, use the left and right BANK
switches.
Note that a channel scrolling function can also be assigned to the Nucleus jog wheel via the Nucleus Remote. Select
TRACKS for the Jog Wheel Default. See Page 24 for more details.
Logic users: Note that the tracks in the session may not appear on Nucleus in the order that they are displayed in the
ARRANGE window unless the ARRANGE Channel Strip View mode is selected in the Logic control surface set up menu.
Basic Channel Parameters
The channel faders and the three switches above them are used for basic control of the DAW channels selected using the
CHANNEL and BANK scrolling functions described above:
- The Nucleus fader controls the DAW channel fader
- The Nucleus CUT and SOLO switches control the DAW channel cut and solo functions.
Note that there is a DAW SOLO LED to the right of the Nucleus logo which lights whenever the solo function is active
within the DAW.
- The Nucleus SEL switch is used to select the channel in the DAW, for purposes such as channel naming. The switch lights
to indicate that it’s corresponding DAW channel is selected. It can also be used for track arming (by pressing the centre
section REC switch – see below), automation (using the centre section AUTO switch – see below) and for assigning plug-
ins to the Nucleus plug-in editor (using the centre section PARAM switch – see Page 36).
Channel Metering
DAW channel meters are replicated at the top of each Nucleus channel strip, above the Mode switch.
Track Arming
The channel SEL switches can be used as track arming switches. To do this, select the REC switch above-left of the MONITOR
LEVEL control. You will notice that the SEL switches now light red and emulate the status of the channel record ready indicator.
Once the REC switch is deselected, the REC LED just below the relevant channel meter lights to indicate ‘Record Ready’ status.
Automation Control
The DAW channel’s automation mode can be controlled by selecting the AUTO switch above-left of the MONITOR LEVEL
control. Use the channel SEL switches to select which channel’s automation mode is being edited, then press the V-Sel
switches to trigger the mode shown in the lower row of the display above them. The upper row of the display will indicate the
selected mode for the selected channel.
Note that the automation modes can be accessed using the V-Sel switches in either side of Nucleus.
HUI Users: Single-letter indication of automation modes can be permanently displayed after the channel name in the
upper row of the display – this is determined by Show Auto Mode in the DAW tab of the Remote. Write modes are
indicated by a flashing
W
, read modes by a flashing
R
, and Off is indicated by no flashing letter. See the Nucleus Remote
Section for more information.
- Nucleus. This is SSL 1
- Document History 2
- Table of Contents 3
- 6. DAW Operations 33 4
- 7. Analogue Operations 39 4
- Appendix 41 4
- Index 45 4
- Introduction 5
- HOW TO USE THIS MANUAL 6
- 1. Nucleus Overview 7
- NUCLEUS REMOTE 8
- 2. Nucleus Configurations 9
- 3. Software Installation 13
- Windows Installation 14
- PHYSICAL CONNECTIONS 15
- Network Wiring 16
- MIDI CONFIGURATION 19
- USB SOUNDCARD CONFIGURATION 21
- 5. Nucleus Remote 23
- REMOTE TABS 24
- REMOTE LAYER SELECTION 25
- LAYER PROFILE CONFIGURATION 25
- Selecting a Profile 26
- TIMELINE FUNCTIONS 28
- SOFT KEY CONFIGURATION 29
- Assigning Soft Key Functions 30
- AW Protocol Commands 31
- AW Keyboard Shortcuts 32
- Page 32 Nucleus User Guide 36
- Blank page – well, nearly 36
- 6. DAW Operations 37
- CHANNEL CONTROL 38
- -Pot and V-Sel Control 39
- PRO TOOLS 39
- MASTER CONTROL 41
- USER KEYS 42
- 7. Analogue Operations 43
- METERING 44
- Appendix 45
- Pro Tools 46
- Nucleus User Guide Page 47 51
Fisher & Paykel no manuali utente
La lista di Fisher & Paykel no prodotti contiene 200 manuali utenti per 127 modelli. Tutte le guide utenti pdf sono disponibili per essere scaricate o visionate online.
Kommentare zu diesen Handbüchern